Built for Your Exact Car
ProClip is made specifically for your year, make, and model — not a universal bracket with foam pads and crossed fingers. It snaps into your dashboard like it was always supposed to be there.
Custom Car Phone Mounts & Holders
Your Car. Your Phone. A Perfect Fit.
ProClip custom-fit mounts and holders built for your car's exact trim. No suction cups, no vent clips, no wobble. Just a trusted hold.
Exact-Fit
Zero Rattles
20+ Years Engineered
ProClip is a 2-part system: a vehicle mount + a device holder. You'll need both for a perfect fit.
Find mounts for your vehicle
400+ vehicles, Exact Fit Design
Two Parts. One Perfect Mount.
The Last Phone Mount
You'll Ever Want.
Limited Time Offer
Snap On. Tee Off.
Dual-magnet system holds firm on cart paths, rough ground, and sudden stops — no bounce, no drop
- MagSafe Compatible
- Any Golf Cart
- 3‑Second Install
- All‑Weather
Shop Now
$29.99
Why ProClip?
Tired of mounts that wobble in your vents, block your view, or fall off mid-drive? ProClip snaps directly into your dashboard and stays put — every road, every ride.
Looks Like It Came With Your Car
No suction cups leaving rings on your windshield. No flimsy vent clip blocking your AC. ProClip blends right into your dash — clean, solid, and exactly where you want your phone.
Set It Once. Done.
Install takes about five minutes. After that, your mount just works — no rattles, no readjusting, no picking it up off the floor at a red light. Solid hold, every single drive.
Upgrade Your Phone, Not Your Mount
Got a new phone? Just swap the holder — your dashboard base stays put. New car? Keep your holder and grab a new base. You never have to start from scratch.
Built for Your Exact Car
ProClip is made specifically for your year, make, and model — not a universal bracket with foam pads and crossed fingers. It snaps into your dashboard like it was always supposed to be there.
Looks Like It Came With Your Car
No suction cups leaving rings on your windshield. No flimsy vent clip blocking your AC. ProClip blends right into your dash — clean, solid, and exactly where you want your phone.
Set It Once. Done.
Install takes about five minutes. After that, your mount just works — no rattles, no readjusting, no picking it up off the floor at a red light. Solid hold, every single drive.
Upgrade Your Phone, Not Your Mount
Got a new phone? Just swap the holder — your dashboard base stays put. New car? Keep your holder and grab a new base. You never have to start from scratch.
Car & Truck Phone Mounts FAQ.
Everything you need to know about your custom dashboard phone mount — compatibility, installation, returns, and warranty.
ProClip is a two-part custom dashboard phone mount system: a vehicle-specific mounting base and a compatible device holder. The base is engineered for your exact make, model, and year — it snaps into the existing seams of your dashboard without drilling or suction cups. The result is a solid, rattle-free fit that no generic vent clip or suction mount can replicate.
Vehicle-Specific Fit
No Drilling
Zero Rattle
Every ProClip system consists of two parts: a vehicle-specific mounting base and a phone holder. The mounting base clips securely into the existing seams of your dashboard without drilling. The phone holder then attaches to that base with four screws included in the box. This modular design means you don't have to start over when your situation changes — upgrade your phone and just swap the holder; get a new car and just get a new base, your holder transfers right over. Use our Product Finder to build the right combination for your vehicle and phone.
Mounting Base
+ Phone Holder
4 Screws Included
Modular Design
Swap & Reuse
ProClip makes exact-fit dashboard phone mounts for over 11,000 vehicle configurations including work vans, service trucks, passenger cars, and commercial vehicles. Supported makes include Ford, Chevrolet, GMC, Ram, Mercedes-Benz, Toyota, Nissan, Isuzu, Hino, Honda, Jeep, Subaru, Volkswagen, and many others. Common work vehicles covered include the Mercedes-Benz Sprinter, Ford Transit, Ford F-150 through F-450, Ram ProMaster, Chevrolet Silverado and Express, GMC Sierra and Savana, and Isuzu NPR box trucks. ProClip also offers mounts for forklifts, golf carts, and specialty equipment used in commercial operations. Find your exact match in our Product Finder.
11,000+ Configurations
Cars / Trucks / Vans
Work Vehicles
Specialty Equipment
Phone mounts are safe to use while driving when they keep your phone visible, accessible, and out of the way of critical controls. The safest mounts install directly on the dashboard within the driver's natural line of sight, leaving the windshield, airbags, vents, and factory controls fully clear. ProClip mounts are engineered to this standard with an exact-fit base that snaps into the seams of the dashboard for a rattle-free hold. There are no suction cups that can release in heat and no vent clips that loosen over time. This keeps the phone secure during emergency braking, rough roads, and daily commercial use. Drivers should still follow all local distracted driving laws and verify any specific requirements that apply to commercial vehicles in their state.
Dashboard Mount
Driver Line of Sight
No Suction Cups
Clears Airbags & Controls
Phone mounts are durable enough for daily commercial use when they are built around a vehicle-specific design rather than a universal bracket. Daily commercial use exposes a mount to constant vibration, temperature swings, slamming doors, rough roads, and 10 to 12 hour shifts, which is where suction cups, adhesives, and vent clips typically fail. ProClip mounts are engineered for these conditions. Each base installs directly into the existing seams of the dashboard for a rock-solid, rattle-free hold with no drilling and no parts that loosen, slip, or release over time. The exact-fit base is machined for each specific year, make, and model, and the two-part design lets operators replace device holders without replacing the base when vehicles or phones change. ProClip mounts are used across fleets, work vans, service trucks, delivery vehicles, field service operations, healthcare, warehousing, manufacturing, public safety, and other professional environments, and carry a one-year warranty against defects in materials and workmanship.
Built for Fleet Use
Rattle-Free Hold
Year-Specific Base
1-Year Warranty
ProClip MagnePro® magnetic holders work natively with MagSafe-compatible iPhones (iPhone 12 through 16 Pro Max). Note that the iPhone 16e does not include MagSafe — it will need a Magnetic Adapter Ring to work with MagnePro holders. MagnePro also works with Qi2 MPP-compatible devices and Pixelsnap-compatible Android phones, as well as any device using a compatible magnetic case or adapter ring.
The Magnetic Adapter Ring is an adhesive rare-earth neodymium ring that sticks to most phones and makes them MagSafe compatible. Browse all magnetic accessories at proclipusa.com/collections/magnetic-accessories.
The Magnetic Adapter Ring is an adhesive rare-earth neodymium ring that sticks to most phones and makes them MagSafe compatible. Browse all magnetic accessories at proclipusa.com/collections/magnetic-accessories.
iPhone 12–16 Pro Max
16e Needs Adapter
Qi2 / MagSafe
Pixelsnap
Adapter Ring Available
Most ProClip custom dashboard phone mounts install in about five minutes. The vehicle-specific mounting base clips into the existing seams and trim gaps of your dashboard with no drilling required. The phone holder then attaches to the base with four screws that are included in the box — a basic screwdriver is all you need. The mount can be fully removed at any time without leaving marks or damage to your interior.
About 5 Minutes
Screwdriver Required
No Drilling
No Dashboard Damage
ProClip accepts returns within 30 days of delivery. A $10 handling fee applies to all returns, which covers the return shipping label and tracking. Items must be returned with all original components included. A 10% restocking fee may apply if items are not returned in original condition. For complete details on eligibility and how to start a return, visit our returns page.
30-Day Window
$10 Handling Fee
10% Restock if Not Original
All Parts Must Be Included
ProClip products carry a one-year limited warranty against defects in materials and workmanship from the date of purchase. Warranty claims are fulfilled by replacement — ProClip does not offer repairs. The warranty does not cover damage caused by misuse, accidents, or unauthorized modifications. For full terms and how to initiate a claim, visit our warranty page or contact our support team.
1-Year Warranty
Defects in Materials
Replacement Only
1-Year Warranty
Every mount is covered against defects in materials and workmanship.
30-Day Returns
Not satisfied? Return within 30 days. See policy for fee details.
Exact-Fit Design
Custom-engineered for your specific year, make, and model — guaranteed to fit.
20+ Years of Engineering
Precision-crafted in Sweden since 2003. Trusted by drivers worldwide.
href="#"
id="pgc-faq-top-btn"
class="faq-cta-btn"
aria-label="Back to top of page">
Back to Top