Choose your country.
Our product information is specific to your location.
We believe you are visiting us from:
This will automatically be set as your ship-to country if you take no action to change it.
-
MENU -
0
We believe you are visiting us from:
This will automatically be set as your ship-to country if you take no action to change it.
Mounting Extension Plates and Angled Wedges
Do you wish you could mount your phone and GPS together on the same mount? Do you have two mobile devices but only one convenient vehicle mount location? Do you want to extend your device sideways from the mount?
Our Extension Plates can do it all - Truly customize your mounting solution!
- Our extension plates allow you to mount two device holders side-by-side
- Extend your electronic device to the left, right or closer to you to avoid interference with other dashboard controls
- Lower or raise your mobile device to keep it in a more upright position for better reception
- 9 Results
NOTICE: The Wedges are not made to stack. Please use only one Wedge per Vehicle Mount
- Adds an additional 15 degrees of angle to your mounting surface
- Can be attached between a mount and a holder
Extend your holder from car mount! These Block Spacers will extend your device holder in two different lengths 14 mm (0.55 in) or 19 mm (0.75 in) from the mount.
WARNING: Block Spacers do not come with screws to mount a heavy duty tilt-swivel. If you have a heavy duty tilt-swivel longer self-tapping screws will need to be purchased separately. Holders that use the heavy duty swivel include certain phone holders, tablet holders, and mobile computing holders. If you are unsure if your holder will work please contact us before ordering to confirm.
- Two different lengths available
- Extend your holder from your car mount or any flat surface
- Screws for attaching the Block Spacer to the car mount are enclosed.
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
This Extension Plate will move a ProClip holder approx. 38 mm / 1.5 inches to the left or right. Use this when you need more space or if your holder is blocking dashboard controls.
- Extend your devices to the left or right of your vehicle mount
- Avoid interference with dashboard controls
- Can be mounted directly to the vehicle mount or to a Tilt-Swivel mount
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
This Extension Plate will move a ProClip holder approx. 25 mm / 1 inch to the left or right. Use this when you need more space or if your holder is blocking dashboard controls.
- Extend your devices to the left or right of your vehicle mount
- Avoid interference with dashboard controls
- Can be mounted directly to the vehicle mount or to a Tilt-Swivel mount
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
This Extension Plate will move a ProClip holder up or down away from the normal mounting position. Use this when you need more space or if your holder is blocking dashboard controls.
- Extends the device upwards or downwards
- Optional add-on for better viewing in certain vehicles
- Works with most ProClip vehicle mounts
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
If you have two devices that you would like to attach to the same mount this extension plate could be for you.
- Keep two devices next to each other on the same mount
- Keeps your devices upright for better reception
- Made of heat and cold resistant ABS plastic
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
If you have two devices that you would like to attach to the same mount this extension plate could be for you.
- Keep two devices vertically one above the other on the same mount
- Keeps your devices upright for better reception
- Can be mounted directly to a vehicle mount or to a Tilt-Swivel adapter
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
Extend your device upwards from the Vehicle Console Mount for better viewing!
- Extend your Device upwards from your Vehicle Console Mount
- Keeps device upright for better reception
- Keeps devices safely at hand
- Can be mounted directly to the Vehicle Mount or to a Tilt-Swivel Mount
Please note: Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
Extend your device upwards from the Vehicle Console Mount for better viewing! Thick version for heavier devices.
- Extend your Device upwards from your Vehicle Console Mount
- Extra thick material for heavy devices
- Can be mounted directly to the Vehicle Mount or to a Tilt-Swivel Mount
- 9 Results
- © 2021 ProClip USA, LLC All rights reserved.
- Ecommerce Website Development by Acumium by Acumium