
Choose your country.
Our product information is specific to your location.
We believe you are visiting us from:

This will automatically be set as your ship-to country if you take no action to change it.

We believe you are visiting us from:

This will automatically be set as your ship-to country if you take no action to change it.
Adapter Plates for Car Mounts
These adapters make it possible for you to attach your own GPS navigation, satellite radio or other mobile device cradle to a ProClip vehicle-specific mount. It's easy, just remove your device or device cradle from its suction cup mount or universal mount and slide it onto a ProClip vehicle mount using one of our adapter plates.
- Ball mount adapters for navigation holders that use a ball mount system
- Plates for mobile devices with a built-in AMPS hole pattern
- Suction cup disks for attaching suction cup holders to your vehicle mount
- Plates to accommodate monitors with thumbscrew holes or rear vertical slots
- Wedge plates to increase the angle of your holder
- 17 Results
This adapter plate has 2 "T" shaped prongs extending out from the base plate. Fits many devices with the "Dual-T" slots; including the Cobb Tuning Accessport.
- 2 Prong / Dual-T Male Adapter
- Includes Tilt-Swivel to angle holder 15 degrees any direction
- Works with any mount that utilizes the AMPS hole pattern
- Comes with 4 self-tapping screws
The threaded adapter allows devices like the GoPro to attach to a ProClip mount.
- 3-Prong threaded mount
- AMPS hole pattern for use with ProClip vehicle mounts or any AMPS base
- Easily attach and remove your device
- Made in Sweden from High Grade ABS Plastic
This adapter plate has 2 "T" shaped prongs extending out from the base plate. Fits many devices with the "Dual-T" slots; including the Cobb Tuning Accessport.
- 2 Prong / Dual-T Male Adapter
- Works with any mount that utilizes the AMPS hole pattern
- Comes with 4 self-tapping screws
- Attach to 75mm existing VESA systems
- Made in Sweden from Durable Machined Aluminum
- 4 - Pre-drilled and 4mm threaded AMPS pattern holes to easily attach ProClip products
Standard website promos do not apply to this item.
- Attach to 75mm and 100mm existing VESA systems
- Pre-drilled 4mm threaded AMPS pattern holes to easily attach ProClip products
Standard website promos do not apply to this item.
NOTICE: The Wedges are not made to stack. Please use only one Wedge per Vehicle Mount
- Adds an additional 15 degrees of angle to your mounting surface
- Can be attached between a mount and a holder
Extend your holder from car mount! These Block Spacers will extend your device holder in two different lengths 14 mm (0.55 in) or 19 mm (0.75 in) from the mount.
WARNING: Block Spacers do not come with screws to mount a heavy duty tilt-swivel. If you have a heavy duty tilt-swivel longer self-tapping screws will need to be purchased separately. Holders that use the heavy duty swivel include certain phone holders, tablet holders, and mobile computing holders. If you are unsure if your holder will work please contact us before ordering to confirm.
- Two different lengths available
- Extend your holder from your car mount or any flat surface
- Screws for attaching the Block Spacer to the car mount are enclosed.
For use with Devices that have a AMPS hole pattern on the back. (30 mm by 38 mm pattern) The Device Mounting Adapter accommodates the AMPS hole pattern in both landscape and portrait.
- Can be used to mount devices that use the AMPS hole pattern
- Keeps your device safely at hand
- Easily remove device from mounting position
- Can be attached to any ProClip vehicle mount or flat surface
- 80 mm (3.15 in) diameter
- Flat surface for suction cup attachment
- 3M adhesive tape to attach to a flat surface
This adapter plate has 1 "T" shaped prong extending out from the base plate. Fits many devices with "Single-T" slots.
- 1 Prong / Single T Male Adapter
- Includes Tilt-Swivel to angle holder 15 degrees any direction
- Works with any mount that utilizes the AMPS hole pattern
- Comes with 4 self-tapping screws
This adapter plate has 1 "T" shaped prong extending out from the base plate. Fits many devices with "Single-T" slots.
- 1 Prong / Single-T Male Adapter
- Works with any mount that utilizes the AMPS hole pattern
- Comes with 4 self-tapping screws
Ball Mount Adapter Plate (17 MM diameter) for use with navigation and other devices/device cradles that use the ball mounting system - usually attached to a windshield suction mount.
- Custom made ball to fit with your device/device cradle
- AMPS hole pattern for use with ProClip vehicle mounts or any AMPS base
- Easily remove device from ball and switch between ProClip mount and original suction cup
The VESA ProClip adapter plate attaches to any existing 75mm and 100mm VESA mounting system to create a new flat mounting surface to allow the attachment of ProClip specific mounts and other mounts/devices.
For VESA devices a ProClip aluminum pedestal is recommended. NOT for use with ProClip vehicle specific mounts.
Please note: This item does not come with mounting screws. Bolts or screws for mounting will need to be obtained separately.
- The VESA ProClip adapter plate attaches to any existing VESA 75mm or 100mm mounting system
- Use to create a new flat mounting surface to allow the attachment of ProClip specific holders
For use with devices/device cradles that use the Richter mounting system - usually attached to a windshield suction cup mount. The Richter system has 4 pins extending out from the plate.
- 4 Prong / Richter Adapter
- Includes tilt-swivel to angle holder 15 degrees any direction
- Works with any mount that utilizes the AMPS hole pattern
This support leg is to be used then you want to convert your current holder into a MultiStand. Easily change the existing tilt swivel to the support leg instead and you will have a completely new holder!
Requires ProClip Tablet Holder, Sold Separately
- Choose the correct size from the drop down box
- Works with holders for tablets sized 7 to 12 inches
- Converts a basic tablet holder into a MultiStand (Tablet holder sold separately)
- Adjustable stand for many angles of viewing
- Made for table/desktop use with rubber non-slip feet
This is a special order item. Please allow an additional 2-3 week lead time.
- Easy self install
- Simply attach in seconds
- When used with a ProClip vehicle mount; no interior damage or drilling of holes
- No special tools required
- 17 Results