• Have Questions?
  • 800.296.3212
  • Skype Us!
  • Click to chat
  • Sign up for emails
.
.

HTC EVO 4G LTE (Sprint) Charging Holder with Tilt Swivel and Straight Power Cord for Fixed Installation

Click to Zoom
Charging Holder with Tilt Swivel and Straight Power Cord for Fixed Installation

Benefits
  • 2 amp charger
  • Rapid and trickle charges device
  • Charging cable permanently attached to holder
  • Straight charging cable for fixed installation
  • Custom fit to your device
  • Holds device securely
  • Keeps your device within easy reach
  • Easily slide device in and out
  • Keeps your device upright for better cellular/GPS reception
  • Neat and discreet design blends well with vehicle's interior
  • Holder can tilt 20 degrees in any direction and swivel 360 degrees
  • Made of heat and cold resistant ABS plastic

Order This Product
Item #: 513403
Price: USD $79.99
Quantity: 
Product Info
How to Install
Compatibility

Avoid cables over your dashboard and always keep your battery fully charged with this high quality custom made holder. It has a neat and discreet design, and keeps your device in an upright position for better reception. A straight power cable is permanently attached to this Holder creating a dock type connection for your device. When your device is slid into the holder it connects to the cable plug. Due to the straight cable you can easily hard wire it behind the dashboard. The Holder angles 20 degrees for optimal viewing. Easily slide your device in/out of the holder. No more fumbling around for your device. Provides for safer driving when viewing, accessing and operating your device in your vehicle.

About the Holder
This Holder works excellent when you don’t want the charging cable hanging from your Holder over your dashboard but at the same time always want your battery fully charged!
The Holder is custom made to fit your device with grooves on the inside walls to match the thickness of the device. This will allow your device to slide freely in/out of the holder. There is no need for you to disconnect any cable or press on any release buttons.
A connector is permanently attached to the Holder’s base. From the back of the Holder's base there is a straight power cable attached. The straight power cable can easily be hidden between/through the dashboard panel sections so you have a clean set up with no cables hanging in front of the dashboard. The holder converts the power from 12 V to 5V. The other end of the cable has bare wires for hard wireing to a permanent power source behind your dashboard. Installation by a professional installer is recommended.

About Our Tilt Swivel
Enlarge ImageThe Tilt Swivel on the back of the Holder can tilt 15 degrees in any direction and swivel 360 degrees. The Tilt Swivel provides easy adjustment of your handhelds position for better viewing, and extends the Holder from the Mount by 20mm / 0.78in. You can also adjust the Holder to avoid unnecessary light reflection. (The Holder shown in the picture to the left is attached to a demo ProClip Mount)
Enlarge ImageThe Tilt Swivel Base Plate on the back of the Tilt Swivel can be attached to any flat surface or mounting brackett. The base plate comes with 6 pre-drilled holes; 2 holes in a center line and 4 holes in an almost square like pattern to accommodate the AMPS hole pattern. Enclosed in the packaging are 4 self tapping screws and 4 machine screws with nuts. Dimensions of base plate: 50mm/1.96inches x 42mm/1.65inches. The 4 holes in the corners have a diameter of 4 mm, and the self tapping screw holes in the center have a diameter of 3 mm.

Keep two devices on the same mount or use one at a time
Click to enlarge imageIf you have two devices you would like to have next to each other on your dashboard you may be able to have them on the same mount as shown in the General Picture to the left, by using our Horizontal Extension Plate.
You can also move a device/holder from car to car (mount to mount) or switch between to devices/holders on the same mount by using our Move Clip System. Please see the product category, Mounting Options, to the left to learn more about these options.

Keep all your devices on the dashboard
If you have more than one device you would like to have on your dashboard, we may have the solution. Usually we have 2 or more mounts for each vehicle model so you can have all your devices securely attached on your dashboard. Many of todays customers order two or more mounts and holders - usually one for their mobile phone and one for their Handheld and/or Music Player like the General Picture below illustrates.
Click to enlarge image

General Illustration Video
Two Part Mounting Solution
.
Stop Fumbling Around  »  Get a Proclip Mobile Mount Today!Learn More
.