ABOUT SSL CERTIFICATES |  | |  |  | | | | Item No. 511015A | | This Adjustable Holder is designed to hold smaller devices used with a skin case, but will also hold devices without a skin case. The buttons and ports on the side of the device may be covered up and the fit may not be a perfect. However, the Holder will still be very convenient to use. The Holder will adjust from a width of 1.9 inches (48 mm) to 2.48 inches (63mm). The thickness of the device the holder can hold is from 0.19 inches (5mm) to 0.57 inches (14.5 mm). The Holder angles 15 degrees for optimal viewing. | | |
|
|
 | | | | Item No. 875214A | | This Adjustable Holder with Tilt Swivel is intended to be used for devices with silicone type cases e.g. iSkin, Jam Jacket, Speck, XtremeMac, Showcase etc. It was originally designed for the Apple iPhone and iPod Touch, but it fits a variety of devices with a skin or case, but the buttons and ports on the side of these devices may be covered up and the fit may not be perfect. The Holder will adjust from a width of 2.5 inches/64 mm to 3.15 Inches/81 mm. The thickness of the device has to be between 0.29 Inches/7.5 mm and 0.47 Inches/12 mm. The Holder angles 15 degrees for optimal viewing. | | |
|
|
 | | | | Item No. 848636A | | This Adjustable Holder with Tilt Swivel was originally designed for all Apple iPod models, including iPod Video, using a shield, skin or case. The Holder will also fit other thicker devices with a skin or case e.g. Smart phones, BlackBerry, PDA, MP3 players etc., but the buttons and ports on the side of these devices may be covered up and the fit may not be perfect. However, the Holder will still be very convenient to use. The Holder width can be adjusted from 2.3 inches (60mm) to 3.2 inches (82mm). The Holder angles 15 degrees for optimal viewing. | | |
|
|
 | | | | Item No. 215052 | | Inner dimensions: 31 x 50 x 6 mm / 1.2 x 2 x 6 inches. Outer dimensions: 50 x 50 x 8 mm / 2 x 2 x 0.3 inches.If you are using a device with a belt clip on the back or a case with a button on the back, you can conveniently hang it in your car or on a wall using the Button and Clip Holder. You do not have to remove your device from its case. The V-slot is designed for the buttons and the opening going through the holder is designed for the clip to slide through. The Button and Clip Holder will accommodate devices, cases, or holsters that have buttons or belt clips. The reason we have a small and a large version of this part is to accommodate the thickness of the bottom part of the clip, which varies from clip to clip, especially for two-way radios. | | |
|
|
 | | | | Item No. 215429 | | This is the same part as the Button and Clip Holder above (Item 205250) but with a deeper pass-through slot for thicker belt clips. Inner dimensions: 31 x 50 x 14 mm / 1.2 x 2 x 0.55 inches. Outer dimensions: 50 x 50 x 16 mm / 2 x 2 x 0.6 inches.If you are using a device with a belt clip on the back or a case with a button on the back, you can conveniently hang it in your car or on a wall using the Button and Clip Holder. You do not have to remove your device from its case. The V-slot is designed for the buttons and the opening going through the holder is designed for the clip to slide through. The Button and Clip Holder will accommodate devices, cases, or holsters that have buttons or belt clips. The reason we have a small and a large version of this part is to accommodate the thickness of the bottom part of the clip, which varies from clip to clip, especially for two-way radios. | | |
|
|
 | | | | Item No. 710620B | | If you can't find a custom holder for your device, our Universal Holder - Stick-on button and V-slot plate, can easily do the job for you. It holds your device securely in place on the dashboard and it doesn't swivel. The adhesive on the back of the Stick-On Button is very strong. The Stick-On Button can be attached to any flat or slightly curved surface e.g. back of cell phone, PDA, Remote Control, Cordless Phone, MP3 Player etc. The V-slot plate can be screwed onto our vehicle dashboard mount or any flat surface. | | |
|
 | | | | Item No. 710771 | | Perfect for use in rental cars, RVs etc.! The Friction Mount can simply be placed on the dashboard. It will keep everything in plain sight when you need it and out of the way when you don't. Attach a Device holder for your device to the face plate and you are all set to go. | | |
|
 | | | | Item No. 215049 | | If you have a Garmin Friction Mount (Bean Bag) and would like to use one of our custom ProClip Device Holders you can attach it with this Angled Extension Plate. | | |
|
 | | | | Item No. 215143 | | Keep your device within easy reach at home or in the office. Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | Item No. 215396 | | Keep your device within easy reach at home or in the office! Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | Item No. 215100 | | Keep a notepad and pen handy. Notepad and pen included. Attaches to any of our ProClip Vehicle Mounts. Not for use while driving. | | |
|
 | | | | Item No. 215265 | | 5-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | Item No. 215264 | | 10-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | Item No. 215083 | | The ProClip Handlebar Mount attaches securely to round handlebars. The Tilt Swivel accommodates all ProClip Device Holders and other device holders with the AMPS Hole Pattern. 1 inch diameter when closed. | | |
|
 | | | | Item No. 215181 | | Do not attach to a ProClip Vehicle Mount. This part is to be used instead of the ProClip Vehicle Mount.Do you need your device closer to you? This goose neck mount will extend your device closer. It can be screwed into any flat surface and the goose neck can be adjusted to face you for optimal viewing. Attach a Holder to the face plate of the mount and you are all set. | | |
|
 | | | | Item No. 215407 | | Do not attach to a ProClip Vehicle Mount. This part is to be used instead of the ProClip Vehicle Mount.Do you need your device closer to you? This goose neck mount will extend your device closer. It can be screwed into any flat surface and the goose neck can be adjusted to face you for optimal viewing. Attach a Holder to the face plate of the mount and you are all set. | | |
|
 | | | | Item No. 215421 | | Angle, tilt, swivel and extend your holder/device for a better viewing position. This mount swivels 360 degrees horizontally and vertically. It extends 2.5 inches/ 62 mm and can be attached to any flat surface. The face plate has several hole patterns including AMPS to accommodate most holders, cradles, mounts and car kits. The face plate is 1.65 x 1.95 inches / 42 x 50 mm. The base plate is 1.65 x 1.95 inches / 42 x 50 mm and it has one hole in each corner. Dimensions: 2.5 x 1.65 x 1.95 inches / 62 x 42 x 50 mm. | | |
|
 | | | | Item No. 945008 | | The Female Car Power Adapter provides the option of additional power outlets in your vehicle. It can also be used as a power source if you want to hard wire your Holder with Cigarette Lighter Cable. | | |
|
 | | | | Item No. 215283 | | A hook for hanging a headset or charging cable neatly in place by your holder. The hook is to be installed between the ProClip Device Holder and the ProClip Vehicle Mount. | | |
|
 | | | | Item No. 215284 | | A hook for hanging a headset or charging cable neatly in place by your holder. The hook is to be installed between the ProClip Device Holder and the ProClip Vehicle Mount. | | |
|
Important Notice |  | You just selected a device mount/holder.
Unless you want to screw it directly into your car dashboard, you also need to order a Vehicle Mount.
The Vehicle Mount creates the platform you need for easy attachment of your device holder without damaging your dashboard. See illustration to the left.
Learn More | | Find Your Vehicle Mount |
Important Notice | | You just selected a Vehicle Mount.
The Vehicle Mount creates the platform you need for easy attachment of your device mount/holder.
Unless you have a holder from before
(not windshield suction cup mount)
we recommend you order a holder for
your device to complete your mounting solution. See illustration to the left.
Learn More | | Find Your Device Holder |
 Shopping Cart Summary
You Just Added ():
-
Total Qty: @
Total: USD $ Items in Your Cart:
Cart Subotal: USD $  Close |
| |
|
|
|
|
