|  | | |  | | The products in this section are real helpers. They help you make your In-Vehicle Mounting Solution even more customized and flexible at the same time. Some of the products also provide the help you need to use your device in a custom way outside your vehicle e.g. a Rental Car, RV, Boat, Home, Office etc. |
|
|
|
|  | | | | | Position your device higher or lower on the mount. If you want to position your device higher or lower from the mount, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface. | | |
|
 | | | | | Our Move Clip System allows you to move your device from vehicle to vehicle or place to place using only one holder. | | |
|
 | | | | | Our Move Clip System allows you to switch between two or more devices using only one dashboard mount. | | |
|
 | | | | | Our Move Clip System allows you to move your device in and out of the vehicle. | | |
|
 | | | | | Add more Female Plates to expand one of the above listed Move Clip Kits or build your own kit. | | |
|
 | | | | | Add more Male Plates to expand one of the above listed Move Clip Kits or build your own kit. | | |
|
 | | | | | Two plate mounting system for mounting and moving small Tablet PCs, UMPC, Monitors, GPS and Satellite Radio devices etc. | | |
|
 | | | | | For use with Devices that have a AMPS hole pattern on the back. (A square like hole pattern) The Device Mounting Adapter accommodates the AMPS hole pattern in both landscape and portrait. | | |
|
 | | | | | For use with Devices that have a AMPS hole pattern on the back. (A square like hole pattern) The Device Mounting Adapter accommodates the AMPS hole pattern in both landscape and portrait. | | |
|
 | | | | | Male Plate: For use with Devices that have a AMPS hole pattern on the back. (A square like hole pattern) The Device Mounting Adapter accommodates the AMPS hole pattern in both landscape and portrait. | | |
|
 | | | | | For use with devices/device cradles that use the Richter mounting system - usually attached to a windshield suction cup mount. The Richter system has 4 pins extending out from the plate. | | |
|
 | | | | | This adapter plate has 2 T prongs extending out from the base plate. Unhook your device from your windshield suction cup mount and slide it onto the 2 T prong adapter used in combination with our Vehicle Mount. The 2 T prong system is used with most Magellan’s, the HP branded iPAQ rx5000 Car Cradle, and many other devices as well. NOTE: Some of the early releases of various Magellan devices only use 1 T prong. If so, please select the 1 T Prong Vehicle Adapter listed below. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | | This adapter plate has 2 T prongs extending out from the base plate, and a Tilt Swivel on the back that provides easy adjustment of your device for better viewing. Unhook your device from your windshield suction cup mount and hook it onto the 2 T prong adapter used in combination with our Vehicle Mount. The 2 T prong system is used with most Magellan’s, the HP branded iPAQ rx5000 Car Cradle, and many other devices as well. NOTE: Some of the early releases of various Magellan devices only use 1 T prong. If so, please select the 1 T Prong Vehicle Adapter listed below. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | | This adapter plate has 1 T prong extending out from the base plate. Unhook your device from your windshield suction cup mount and slide it onto the 1 T prong adapter used in combination with our Vehicle Mount. The 1 T prong system was used with early versions of some Magellan’s and many other devices. NOTE: The newer releases of various Magellan devices use 2 T prongs. If you have this, please select the 2 T Prong Vehicle Adapter listed above. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | | This adapter plate has 1 T prong extending out from the base plate, and a Tilt Swivel on the back that provides easy adjustment of your device for better viewing. Unhook your device from your windshield suction cup mount and slide it onto the 1 T prong adapter used in combination with our Vehicle Mount. The 1 T prong system was used with early versions of some Magellan’s and many other devices. NOTE: The newer releases of various Magellan devices use 2 T prongs. If you have this, please select the 2 T Prong Vehicle Adapter listed above. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or a 2 prong T extending from the mount. | | |
|
 | | | | | Angle your holder/device for a better viewing position. If you want to angle your holder/device for a better viewing position the Tilt Swivel Mount will make it possible. It angles approx 15 degrees and swivels 360 degrees. | | |
|
 | | | | | Angle your holder/device for a better viewing position. Same as item no. 213018 above but it extends from center to better avoid interference between your device and dashboard buttons, gear shift etc. | | |
|
 | | | | | Tilt Swivel Mount, Large for installation of heavier devices such as larger monitors, laptops etc. Allows you to adjust the angle of the device and provides a flexible yet firm installation. | | |
|
 | | | | | Extension mounting plate, angled 15°. With 6 predrilled holes. | | |
|
 | | | | | Extension mounting plate, angled 10°. With 6 predrilled holes. | | |
|
 | | | | You do not have to remove your device from its case!
The V-Slot Button & Clip Holder will accommodate devices, cases, or holsters that have buttons or belt clips. | | |
|
 | | | | | Fits Full size iPods, some Smart Phones, MP3 Players, PDAs etc as long as the device is wide enough. NOTE: This Holder is adjustable and is intended to be used for devices with silicone type cases e.g. iSkin, Jam Jacket, Speck, XtremeMac, Showcase etc. | | |
|
 | | | | | If you can't find a Holder for your device/phone, this option works very well! Our "Universal Holder" - Stick-on button and V-slot plate - holds your device securely in place on the dashboard and it doesn't swivel. | | |
|
 | | | | | Perfect for use in rental cars! The ProClipTravel Mount attaches to the windshield with a suction cup. | | |
|
 | | | | | Keep your device within easy reach at home or in the office! Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | | Keep your device within easy reach at home or in the office! Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | | Keep a notepad and pen handy! Notepad and pen included. Attaches to any of our ProClip Vehicle Mounts. Not for use while driving. | | |
|
 | | | | | 5-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | | 10-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | | The ProClip Handlebar Mount attaches securely to round handlebars. The Tilt Swivel accommodates all ProClip Device Holders and other device holders with the "AMPS Hole Pattern". 1" diameter when closed. | | |
|
 | | | | | Not to be used in combination with a ProClip Vehicle Mount, this part is to be used in place of a ProClip Vehicle Mount. Do you need your device closer to you? This goose neck mount will extend your device closer. It can be screwed into any flat surface and the goose neck can be adjusted to face you for optimal viewing. Attach a Holder to the face plate of the mount and you are all set. | | |
|
 | | | | | If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item # 213018) | | |
|
 | | | | | The ProClip Suction Cup Adapter Plate will allow you to attach your suction cup directly to your Vehicle Mount. | | |
|
|
| |
|
|
|
| |
|
