ABOUT SSL CERTIFICATES |  | |  | The Extension Plates help you keep two devices next to each other on the same mount, extend your device to the left or right to avoid interference with other dashboard controls, lower or raise your device, keep it in a more upright position for better reception etc. – truly customize your mounting solution.
|
|
|
|
|  | | | | Item No. 215397 | | Keep two devices next to each other on the same mountIf you want to have two devices attached next to each other, this is what you are looking for. The Horizontal Extension Plate attaches to the ProClip Vehicle Mount or Tilt Swivel directly. It has several hole patterns e.g. for the ProClip standard (two holes in a center line) and the AMPS standard (Four holes in an almost square pattern) The Horizontal Extension Plate can hold either 1 vertical device and 1 horizontal device or 2 vertical devices next to each other. Dimensions: 155 x 50 x 5 mm / 6.10 x 1.97 x 0.19 inches. | | |
|
 | | | | Item No. 215395 | | Avoid interference with the dashboard controls/displays when using wide devices! If you want to extend your device to the left or right from the Vehicle Mount (especially the ProClip Angled Mount) to avoid interference with the dashboard controls/displays, this is what you are looking for. This extension plate is only to be used with one device. | | |
|
 | | | | Item No. 213065 | | Position your device higher or lower on the mount. If you want to position your device higher or lower from the mount, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface. | | |
|
|
 | | | | Item No. 215437 | | Keep two devices above each other on the same mount.If you want to have two devices attached above each other, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Vehicle Mount or Tilt Swivel directly. It has several hole patterns e.g. for the ProClip standard (two holes in a center line) and the AMPS standard (Four holes in an almost square pattern) The Vertical Extension Plate is primarily designed for use with the Garmin Nuvi Ball Mount, TomTom Active Docks, Magellan 1 and 2 Prong Mounting Plates and the Richter 4 Prong Mounting Plate, which attaches at the bottom of the plate plus one other device to be attached on top of the plate. Dimensions: 155 x 50 x 5 mm / 6.10 x 1.97 x 0.19 inches. | | |
|
|
 | | | | Item No. 215228 | | If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item # 215453) | | |
|
 | | | | Item No. 215413 | | If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item number 215453) | | |
|
 | | | | Item No. 215450 | | Extend your holder from car mount! This Block Spacer will extend your device holder/mount 14 mm/ 0.55 inch from the car mount. Screws for attaching the Block Spacer to the car mount are enclosed. | | |
|
 | | | | Item No. 215451 | | Extend your holder from car mount! This Block Spacer will extend your device holder/mount 19 mm/ 0.75 inch from the car mount. Screws for attaching the Block Spacer to the car mount are enclosed. | | |
|
Shopping Cart Summary
You Just Added ():
-
Total Qty: @
Total: USD $ Items in Your Cart:
Cart Subotal: USD $ Close |
| |
|
|
|
|
