ABOUT SSL CERTIFICATES |
 |
 |
| This Vehicle Mount is one part of the ProClip 2 Part Solution. To keep your device attached to this mount, you will need to order a Holder specific to your device. After selecting your Mount, please select Device Holders on the upper left side and choose your device from the drop down menus to complete your order. Note: if you already own a device holder or have already selected one, please disregard this information. |
|
|
|
|
|
|
| Item #: 853465 |
| Price: USD $29.99 |
|
|
|
- Simply clip on in seconds
- Anyone can do it
- No special tools required
- No dashboard dismantling
- No interior damage
- Secure fit within easy reach
- Made of heat and cold resistant ABS plastic
- Pre-drilled holes for AMPS and ProClip hole patterns
- Onto the ProClip Mount you can attach any type of holder for your device e.g. a Mobile Phone, MP3, PDA, PND, GPS, UMPC, Satellite radio, Navigation Monitor, Multimedia Monitor, Hands-free car kit, Two-way radio etc.
|
|
|
|
|
|
 |
Product Info |
 |
|
|
|
 |
How to Install |
 |
|
|
|
Compatibility |
|
|
|
|
|
|
| This easily self-install Dashboard Mount is custom made and clips into the seams between the panel sections of the dashboard, providing a very sturdy and tight fit. Average installation time is 30 sec. to 2 minutes. (See confirming article in The New York Times) No dismantling of your dashboard is required and there is no damage to your vehicle’s interior! The ProClip Mount is made of ABS plastic and is heat and cold resistant. |
|
ProClip face plate hole patterns |
 The face plate has several hole patterns – one with four holes in a center line and one that have four holes in a square-like pattern to accommodate the AMPS standard.
If you have a device/holder/cradle with a different hole pattern you can always drill new holes to match your device or simply use self tapping screws and screw directly into the faceplate. |
|
Keep two devices on the same mount or use one at a time |
 If you have two devices you would like to have next to each other on your dashboard you may be able to have them on the same mount as shown in the General Picture to the left, by using our Horizontal Extension Plate.
You can also move a device/holder from car to car (mount to mount) or switch between to devices/holders on the same mount by using our Move Clip System. Please see the applicable product categories the left to learn more about these options. |
|
Keep all your devices on the dashboard |
|
| If you have more than one device you would like to have on your dashboard, we may have the solution. Usually we have 2 or more mounts for each vehicle model so you can have all your devices securely attached on your dashboard. Many of todays customers order two or more mounts - usually one for their mobile phone and one for their Handheld and/or Music Player like the General Picture below illustrates. |
|
 |
|
|
|
| Make |
Model |
Year |
| Acura |
TL |
2004.0 - 2008.0 |
|
|
 |
|
|
|
|
|
Installation instruction |
|
|
 1.
Press the thin end of the enclosed gap opener into the gap between the console edge panel frame and the padded console edge, to widen the gap.
|
|
 2.
Peel off the cover of the adhesive tape on the ProClip and place it in your hand so the three center lined holes are towards the top.
Place the ProClip over the console edge so the left side of the ProClip attaches to the inside of the console edge.
|
|
 3.
Press firmly forward on the right side of the ProClip so the angled edge goes into the gap below the gap opener. Press until you see or hear/feel it snaps into place. Pull out the gap opener.
The ProClip is now in place as shown in the overview picture above.
|
|
|
|
|
|
 + '&width=480&height=480&pageid=8686', 'imagepopup', 480, 480);)
;)
;)
;)
;)
;)