ABOUT SSL CERTIFICATES |
 |
|
Apple iPod Touch 1st Gen. - Charging Holder with Tilt Swivel and Cigarette Lighter Adapter
|
 |
| This Device Holder is one part of the ProClip 2 Part Solution. To mount this in your vehicle, you will need to order a Mount specific to your vehicle. After selecting your Holder, please select Vehicle Mounts on the upper left side and choose your vehicle from the drop down menus to complete your order. Note: if you already own a vehicle mount or have already selected one, please disregard this information. |
|
|
|
|
|
|
| Item #: 710777 |
| Price: USD $69.99 |
|
|
|
- Rapid and trickle charges device
- Charging cable permanently attached to holder
- Custom fit to your device
- Holds device securely
- Keeps your device within easy reach
- Easily slide device in and out
- Keeps your device upright for better cellular/GPS reception
- Neat and discreet design blends well with vehicle's interior
- Holder can tilt 15 degrees in any direction and swivel 360 degrees
- Made of heat and cold resistant ABS plastic
|
|
|
|
|
|
 |
Product Info |
 |
|
|
|
 |
How to Install |
 |
|
|
|
Compatibility |
|
|
|
|
|
|
About the Holder |
|
| Do you always need your battery fully charged? This Holder is the perfect solution for you! There is a cigarette lighter cable permanently attached to the base of this Holder so when your device is slid into the holder it connects to the cable plug. |
|
|
| The Holder is custom made to fit your device with grooves on the inside walls to match the thickness of the device. This will allow your device to slide freely in/out of the holder. There is no need for you to disconnect any cable or press on any release buttons. |
|
About Our Tilt Swivel |
 The Tilt Swivel on the back of the Holder can tilt 15 degrees in any direction and swivel 360 degrees. The Tilt Swivel provides easy adjustment of your handhelds position for better viewing, and extends the Holder from the Mount by 20mm / 0.78in. You can also adjust the Holder to avoid unnecessary light reflection. (The Holder shown in the picture to the left is attached to a demo ProClip Mount) |
|
 The Tilt Swivel Base Plate on the back of the Tilt Swivel can be attached to any flat surface or mounting brackett. The base plate comes with 6 pre-drilled holes; 2 holes in a center line and 4 holes in an almost square like pattern to accommodate the AMPS hole pattern. Enclosed in the packaging are 4 self tapping screws and 4 machine screws with nuts. Dimensions of base plate: 50mm/1.96inches x 42mm/1.65inches. The 4 holes in the corners have a diameter of 4 mm, and the self tapping screw holes in the center have a diameter of 3 mm. |
|
|
Keep two devices on the same mount or use one at a time |
 If you have two devices you would like to have next to each other on your dashboard you may be able to have them on the same mount as shown in the General Picture to the left, by using our Horizontal Extension Plate.
You can also move a device/holder from car to car (mount to mount) or switch between to devices/holders on the same mount by using our Move Clip System. Please see the product category, Mounting Options, to the left to learn more about these options. |
|
Keep all your devices on the dashboard |
|
| If you have more than one device you would like to have on your dashboard, we may have the solution. Usually we have 2 or more mounts for each vehicle model so you can have all your devices securely attached on your dashboard. Many of todays customers order two or more mounts and holders - usually one for their mobile phone and one for their Handheld and/or Music Player like the General Picture below illustrates. |
|
 |
|
|
|
| Make |
Model |
| Apple |
iPod Touch 1st Gen. |
|
|
 |
|
|
|
|
|
 + '&width=480&height=480&pageid=13859', 'imagepopup', 480, 480);)
;)
;)
;)
;)